top of page
test banner 5 2024.jpg

GTS 41

The GTS 41 is our largest and most popular top-loading kiln and is built with a fiber lid to offer light weight and a clean firing. Firebrick lids are heavy and can unleash unwanted particles into the glass surface. Not so with our fiber lid.

The fiber lid of the GTS 41 delivers a clean firing while retaining all the benefits of a firebrick chamber. The best of both worlds, combined to create our largest and best selling top loading glass kiln.

Features

Fiber Lid

The lid of the GTS 41 is constructed of a fiber material that provides excellent thermal properties along with light weight. This design allows the heating elements to be positioned on the surface for maximum heat transfer and firing efficiency.

The fiber chosen for the lid is an extremely low-shot material. The surface is then covered with a no-shot fiber sheet. These two materials combine to create a lighter weight lid while severely limiting any debris from the lid falling onto the glass. Very nice.

Top Load

The GTS 41 is a top loading design and offers a chamber 41" wide x 25.25" long x 13.5" deep. The rim of the chamber is 32" off the floor which is at waist height or lower making it very easy to load and position your glass.

Fiber and Firebrick Design

The GTS 41 is constructed of both fiber and firebrick.

The entire lid of the GTS 41 is constructed of fiber to reduce the overall weight of the lid as well as severely limiting lid debris.

The walls and floor are made of firebrick which is desired in a glass kiln as it stores heat in the beginning of the firing which acts to smooth out temperature swings. It then releases heat slowly at the completion of the firing resulting in awesome annealing. It's just beautiful.

The GTS 41, like the related Studio Pro models, artfully combines two great materials to produce one of the best glass kilns out there.

Swing View Equipped

GTS 41 temperature controls are fitted to our Swing View Adjustable Enclosure.
 
The swing view is a pivoting, swing-up enclosure that allows you to rotate the control to a comfortable viewing and programming angle. Once you're done, lay it back down to see it from across your studio. It's that simple.
 
The swing view pairs well with touchscreen controls like the TAP II, Icon+ and Icon as viewing angle can be perfectly aligned. You'll love it.

2 Position Lid Vent

The GTS 41 is equipped with a 2 position lid vent.

The lower vent position props the lid by about an inch. Perfect for venting off adhesives and other low temperature binding materials.

The upper vent position props the lid by about 4 inches. Perfect for speeding up the cooling process.

Relay Access Port

The GTS 41 incorporates our Relay Access Port for simple, no-panel-off relay replacement.

Simply remove the access plate to gain access to the mechanical relays. There's no need to remove the control panel and dig into the internal wiring. It's absolutely simple and effective and all it takes is a screwdriver!

It's a given that mechanical relays will fail at some point. This relay access port really comes in handy when they do.

Maintenance Parts Tag

To assist you in replacing worn items we have included a maintenance parts tag on the GTS 41 indicating the proper Evenheat part numbers for anticipated maintenance items.

Wish we had this decades ago.

Power Interrupt Switch

The GTS 41 is standard equipped with a power interrupt switch which removes electrical power from all heating elements if the lid is opened.

 

This is important for those who may access the kiln during firing such as glass manipulation.

Build Options

Multiple Control Options

The GTS 41 is available in a variety of controls including the Icon, Icon+, Tap II and Rampmaster 3.

At Evenheat we take the best control platforms on the market and make them even better by adding Special Limits thermocouples for precise temperature sensing and non-metallic faceplates for stellar Wi-Fi reception for on-line Apps. Visit our Controls tab to learn more about our controls and why they represent the very best that you can get.

Quiet Drive Solid State Relay Option

GTS 41 models are available with our Quiet Drive Solid State Relay option.

Our Quiet Drive Solid State Relay System offers tight temperature control, high reliability and increased heating element life. The Quiet Drive is arguably the best designed and best performing solid state system on the market.

Rolling Option

The GTS 41 is easily made mobile with our rolling option.

The GTS 41 base is equipped to accept our casters. No frame or extra hardware required. Simply attach the casters to the standard base and you're ready to go!

Casters are not factory installed. You will install them when you first set up your kiln. It's designed to be easy and it is. They can always be added later as well.

evenheat-circle-e red.png

Voltage Options

Our default production for the GTS 41 is 240V, Single Phase.

 

We do offer to build in 200V, 208V, 220V and 230V by request.

All controls available on the GTS 41 will operate properly on both 50Hz and 60Hz line frequencies. To say it another way, line frequency has no effect. It doesn't matter.

Evenheat recommends that you check your operating voltage before ordering or placing the kiln in service.

evenheat-circle-e red.png

Voltage Phase Options

The GTS 41 is available in 3 phase Delta and Wye (380V, 400V and 415V) designs by request.

Specifications

GTS 41

Chamber Dimensions:

25.25" L x 40.5" W x 13.5" D - 7.52 Cubic Feet

(64.1cm L x 102.9cm W x 34.3cm D - 213L)

Outside Dimensions:

30.25" L x 56" W x 29.5" H (with 8" stand)

(77cm D x 142m W x 75cm H)

Maximum Use Temperature:

1800°F (982°C)

Standard Electrical:

240 Volts, 45 Amps, 10,800 Watts, 50/60Hz, Single Phase

Power Cord Plug Configuration - NEMA 6-50

Available in 200V, 208V, 220V and 230V by request

Operates properly on both 50Hz and 60Hz

Available in 3 phase Delta and Wye  (380V, 400V and 415V) designs

Consult with an electrician for proper fuse panel, service wire size, receptacle, and fusing requirements. This model, used for its intended and expected purpose, would not be defined as "continuous use". Continuous use is defined as continuous, full power on for 3+ hours.

Weight:

335lb. (152Kg) - Approx.

Shipping Method:

Freight Truck

NRTL Listing Agency - TUV Listed United States and Canada - Designed and Tested to CSA & U/L 499

California Prop 65
GTS 41 models may contain chemicals known to the State of California to cause cancer and birth defects or other reproduc
tive harm.

Accessories

GTS 41 Full Shelf Furniture Kit

1 - Full Shelf - 38" x 22-5/8" x 1" (5.2 square feet)

12 - 2" Posts

1 - 6 Reed Haik Brush

1 - 24oz. Shelf Primer - Hotline Hi-Fire Brand

The full shelf is a seamless shelf that's 1" thick and offers 5.2 square feet of firing surface.

 

We recommend using all 12  posts, spaced accordingly. Any posts should be at least 2" or more. We do not recommend posting the shelf lower than 2" or placing it directly on the kiln floor.

GTS 41 Half Shelf Furniture Kit

2 - Half Shelves - solid (not as shown)

12 - 1" Posts

1 - 6 Reed Haik Brush

1 - 24oz. Shelf Primer - Hotline Hi-Fire Brand

When shelves are used together there is a single seam that runs down the middle, front to back. We recommend that you always use posts under your shelf to raise it off the floor. This kit comes with 1" posts for this purpose. You are welcome to any use size post you wish. We do not recommend placing the shelf directly on the kiln floor.

From a handling standpoint, the half shelves are easier to manage than the single, full shelf.

GTS 41 Full Shelf

Full Shelf - 38" x 22-5/8" x 1" (5.2 square feet)

The full shelf is a seamless shelf that's 1" thick and offers 5.2 square feet of firing surface.

 

We recommend using 12  posts, spaced accordingly. Any posts should be at least 2" or more. We do not recommend posting the shelf lower than 2" or placing it directly on the kiln floor.

GTS 41 Half Shelf

Half Shelf - Two shelves are needed to create a full firing surface.

 

We recommend that you always use posts under your shelf to raise it off the floor and suggest starting with 1" posts. You are welcome to use any size post you wish. We do not recommend placing the shelf directly on the kiln floor.

Posts

We offer shelf posts ranging from 1/2" to 6". In general you will always want to post up your firing shelf. We recommend using at least a 1/2" post.

Haik Brushes

Our Brushes are a wide and very soft brush used to apply shelf primer.

Shelf Primer - 24oz. (Dry)

Shelf primer creates a layer of protection between the kiln shelf and your glass as it prevents your glass from sticking to the shelf. It is generally applied using a soft brush like our Haik brush. It can also be airbrushed on with the proper equipment.

 

Our shelf primer of choice is a Hotline product called Hi-Fire. It's supplied in dry form and is mixed with water for application onto the kiln shelves.

bottom of page